Looking for validation simulation templates? Sign up for SimScale and join the largest engineering simulation community in the world! | Page 1

Simulación de análisis de elementos finitos para determinar los esfuerzos presentes en un tanque a presión de pared gruesa.

Utilización básica de elementos finitos.

A wind simulation on a rectangular block to validate hand calculations.

This simple project presents the uniaxial tension test of Aluminium 6061-T6 and 6063-T5.

The purpose of this test case is to validate the mean surface pressure on a building with balconies, using the Lattice Boltzmann model for three wind directions.

The aim of this test case is to validate the following parameters of incompressible steady-state laminar fluid flow through a pipe.

In this project a static analysis of a shaft subjected to a user defined rotation and a cyclic boundary condition is demonstrated. The objective is to evaluate a shaft consisted of a single part against a shaft split in half.

The work aims to validate the analysis in CFD to enable the application in more complex geometries.

This projects validates the incompressible flow simulation results of SimScale around the Ahmed body.

Validation case using a WES weir to test the accuracy

In this project incompressible fluid flow simulation of a conical draft tube is carried out. The parameters data is collected from the course book on fluid dynamics and the validation of CFD simulation result with the theoretical result is also performed. Steady state incompressible fluid flow simulation is selected for the given case.
The draft tube is a pipe of gradually increasing area, which connects the outlet of the water turbine's runner to the tail race. Draft tube helps to convert the exit velocity head into pressure or potential head.

validation of beam deflection with different types of support (Bessel, Airy, end) under gravitational load. Comparison with analytically solution.

Finite Elements Analysis of the stress distribution and deformation of a road pavement section, including the top Hot Mixture  Asphalt and lower layers of different materials. The goal is to replicate results in a published paper, where the method is used to estimate HMA stiffness module from field measured stress and deformation values.

NACA 0012 airfoil from NASA's TMR website.

The aim of this project is to calculate the pressure drop in turbulent flow through a straight smooth pipe. Airflow inside a smooth pipe, which has 4 mm of diameter and 2 m length, was simulated for 50, 40, 30, 20, and 10 m/s inlet velocities.  Incompressible steady-state flow analysis with k-omega SST turbulence conditions is considered for the flow. The results from the CFD study are compared with those from an analytical study for validation purpose. It was noted that using SimScale even with automatic meshing as well as solver settings, high accuracy can be achieved.

This validation focuses on validating the moment coefficients using experimental results obtained by RWDI in their wind tunnel tests, published in the paper (Calin Dragoiescu, Jason Garber and Suresh Kumar, 2006) where results were published using two techniques, a high-frequency force balance (HFFB) and high-frequency pressure integration (HFPI) which uses tap points. Both showing mostly good agreement between the two, with HFFB expected to be more accurate.

External flow simulation for the reference SAE notchback model

To verify the setup to be used in analysing aerodynamic bodies

To validate CFD results against the Architectural Institute of Japan's Case F results both from the field and wind tunnel,

Case covered in the Academics Week of Mechanical Engineering - SAEM2018, Brazil. https://saem.unifesspa.edu.br/

The purpose of this project is to use experimental results from the Architectural Institute of Japan to validate CFD results gained from SimScale. The case being validated is Case E, which consists a complex of buildings with simplified geometry. Many scenarios are presented in Case E, The scenarios used to validate the SimScale platform were the North, East, South and Westerly winds for the after construction scenario.

The SimScale CFD results were compared to the experimental results and found to have good correlation. Some underprediction was seen in the k-epsilon models in the strong wind regions and underprediction in the wake regions, but is a known trait of the K-epsilon model and is acceptable and should be considered when evaluating results.

The purpose of this project is to use experimental results from the Architectural Institute of Japan to validate CFD results gained from SimScale. The case being validated is Case D, which consists of a single high-rise building, surrounded by blocks of simplified buildings. The geometry used was the scaled geometry from the data file provided by the Architectural Institute of Japan, and measurements were taken at points also listed in the data file.

The purpose of this project is to validate the accuracy of the solver for transport and distribution of Gas (passive scalar) in an indoor environment.The airflow pattern (velocity) and concentration results from CFD are to be compared with experimental data obtained from full-scale tests.

Conjugate heat transfer validation. Air flow over a plate is considered for this case. The setup of CFD model and comparative results are explained in SimScale forum comments section of this project.

NASA's Turbulence Modelling Resource was created with the purpose of offering documentation on the various RANS turbulence models available and some reference cases to verify the implementation of such models.

Albeit the differences in  the implementation of the models in OpenFOAM and NASA documentation, with this project we will see if we can get comparable results.

This project simulates instantaneous turbulent wake of a cylinder body via LES method.

6 DOF validation test for free heave motion of floating cylinder

This project simulates the air flow around the Ahmed body for validation purposes.

This project simulates Couette flow - flow in annulus fixed-rotating cylinder pair.

This project simulates the reattachment phenomenon over a backward-facing step.

This project simulates incompressible non-newtonian flow through a sudden expansion.

This project performs a heat transfer analysis of a sphere under convection.

This project conducts a dynamic analysis of a pinned bar under gravitational load.

In this validation project, a dynamic nonlinear impact analysis of an elastoplastic bar is demonstrated.

This project validates distributed pressure and nodal stresses for a thick plate under pressure load.

In this project a static analysis of a beam und a gravitational load is demonstrated.

This project performs a frictionless contact analysis between two spheres.

validation | SimScale Project Library | Page 1