Looking for multiphase simulation templates? Sign up for SimScale and join the largest engineering simulation community in the world! | Page 1

Assessment of the water level of a cooling tower water distribution open channel.

The channel has a water inlet and numerous holes for outlet, while it is open to the atmosphere.

Three different designs are evaluated to optimize the filling performance. Watch our on-demand webinar about Multiphase capabilities where this case is presented in more detail
https://www.simscale.com/webinars-workshops/new-multiphase-flow-capabilities/

USA.VIRGIN ISLANDS POWERFUL MAGIC RING TO BOOST BUSINESS +27639132907 INCOME INCREASE,MAKE YOU RICH AND FAMOUS,CUSTOMER ATTRACTION IN BRITISH VIRGIN ISLANDS,NOVA &SCOTIA/PRINCE EDWARD ISLANDS,CANADA,      +27639132907 MAMABWEZA POWERFUL MYSTIC MAGIC RING TO BOOST BUSINESS,INCOME INCREASE,PASS EXAMS,JOB PROMOTION ,BRING BACK LOST LOVER,STOP BAD LUCK,SOLVE FINANCIAL PROBLEMS,BOTSWANA POWERFUL MAGIC RING FOR CHURCH LEADERS,PASTORS,PROPHETS TO GET CHURCH POWER,PROTECTION DO ACCURATE PROPHESY  IN  SOUTH AFRICA,WELKOM,FREE STATE,MPUMALANGA,LIMPOPO,CAPE TOWN,PORTELIZABETH,EASTERN CAPE

Resistance calculation on a semi-planing trimaran hull

Retrying Trimaran analysis without symmetry and using metric units

This part of the project on design and analysis of the spray drying system for drying of milk that we did in our final year of undergraduate studies in Mechanical Engineering at Kathmandu University, Dhulikhel, Nepal.

Poorly made and inaccurate simulation of an AC 75 foil piercing the surface  in windward mode. Note profiles and geometry are guessed at best

The test of waterfall masterclass but with new geometry

Check out www.simscale-academy.com for more classes on simulation.

The aim is to simulate water stream leaving the nozzle.

Multiphase simulation of fuel slosh inside rocket tank.

PUCV Lab Project - Obstacles in Open Channel

In this exercise, you will work with the hex-parametric mesher to mesh a valve geometry. Check out www.simscale-academy.com for more classes on simulation.

Hydrokinetic Banki cross flow turbine for rural areas  whit bidirectional diffuser augmented (BDA).

Hydrokinetic is a recently introduced type of hydropower energy, having been proven as the most
effective and predictable renewable energy source available around the world, especially in the rural and
electrification areas. Most of these sites are dependent on small and micro scale stations to produce
cheap but abundantly available and effective electrical energy. Hydrokinetic energy that can be harnessed from the flow of water in the irrigation and rainy channels is a promising technology in countries
with vast current energy. Micro hydrokinetic energy scheme presents an attractive, environmentally
friendly and efficient electric generation in rural, remote and hilly areas, as effort to reduce the everincreasing greenhouse gas emissions and fuel prices in these sites. (1)

This simulation is based in the reasearch of A.H. Elbatran et al.
https://doi.org/10.1016/j.oceaneng.2018.04.042 and is maded for the simscalecontest2019

In this project, the fluid flow direction in a rotating system is investigated. This project aims to recreate an experiment that I saw some while ago. This experiment is a container with hoses, that are able to rotate around the centre of the container. The hoses are either pointing out of the centre of rotation or pointing toward  the centre of rotation. Consider the hoses pointing outward, if we rotate the system the water leaves in the opposite direction as the hoses are moving. Counterintuitively, when the hoses point toward the center, the water leaves in the same direction as the hoses are moving. The simulation is a multiphase simulation with a rotating zone.

Full details about the simulation, the experiment and additional information is provided in the comments.

This project is dedicated to mechanical durability of plastic box, which used in concrete cubic tests. There are strong mechanical and stress forces influence on this small plastic box. Simulation should help us to calculate - how many times could be used this box till it will be finaly damaged.

the project goal is to design a new modified wet sump for Honda CBR600RR Engine, to prevent oil sloshing baffles  must be used so I need to simulate the motion of the oil in the sump when affected by lateral and longitudinal acceleration.
this project is for Formula Student car

A vehicle drive through simulation wherein the water passes through high level of water surface. This involves multiphase  modeling

This project demonstrates a multiphase flow simulation of a waterfall.

In this project a multiphase flow simulation of a stirred reactor is demonstrated.

A Multi-phase flow simulation for filling of a vehicle fuel tank that is initially filled with Air.
Originally done by dheiny.

multiphase | SimScale Project Library | Page 1