Looking for conjugate heat transfer simulation templates? Sign up for SimScale and join the largest engineering simulation community in the world! | Page 2

Vediamo se qui viene della turbolenza e migliora lo scambio di calore

This project is to test the pressure drop and heat transfer characteristics of microchannel cooling and to optimize it

Single channel coldplate, different configuration

Gak ad detail u/ menghemat pemakaian mesh dan CH

Flow through a curved heat sink with various fin configurations.

Heat Transfer Analysis of a Spiral Heat Exchanger: In this project Conjugate Heat Transfer Simulations were performed to find out temperature distribution inside the heat exchanger. From the temp. distribution, outlet conditions were obtained to evaluate the effectiveness of this particular configuration.

Trying to simulate natural convection over a horizontal cylinder placed over a stage

Thermal simulation of electronics in a housing.

This project simulates a solid-state relay under a 15W heat load. 
This relay includes a heat sink that acts as a fixture from the relay housing to the mounting wall. The product is tested under natural convection conditions at 20C. 

Credits to Xinchao Song for the 3D model used in this project.  Link : https://tinyurl.com/ycd6cvug

In this Project we Simulate an Exhaust Manifold using CHTV2.0 Simscale solver 

The goal is this project is to understand the Heat transfer between the exhaust gases and the manifold, Thermal stresses on it as well as heat transfer coefficient accuracy & predictions. We evaluate areas of higher velocity and temperature variation and perform more detailed analysis on it to find out what kind of condition to expect at the outlet of the exhaust, how to improve its performance and much more !

Conjugate heat transfer simulation in a U tube Heat exchanger using CHT 2.0 Solver of SimScale.

Test natural and forced convection with conjugate heat transfer of a heat sink.
Added thermal pad as thin layer resistance and small flow region as enclosure.

CHT Simulation of a flow through pipe.  Gasoline is transported through pipes among other ways. In this simulation the low temperature gasoline is being transported through a pipe of higher temperature found generally at sunny areas outside city limits reaching up-to 55 deg. We simulate how the gasoline temperature varies under such conditions. The fluid property change under varied thermal loads can vary & hence its important to simulate it before we manufacture. Pipes are used throughout the world for transporting N number of products & hence even though appears basic, proper analysis is highly profitable in the longer run for the life of material & fluid product.

Intended designing a simple and sustainable, desalination system that's used to purify contaminated water by using reliable methods. The project is inspired by the global water crisis seen in the news & mainstream.

Testing heat transfer for a project prototype

Description: there is a plate glass and window, the other elements are made out of steel

Conjugate heat transfer modelling of rotating and heated cone.

This simulation aims a determining whether the temperature of the board of 2x 160W COB Series UV LED is below the recommended temperature of 40C  with a water cooling block running with 0.2m/s inlet velocity.

3D model from Philippe Cavalier (https://grabcad.com/library/water-cooling-led-heatsink-1)

Here I'm going to use conjugate heat transfer to simulate the  heat flow between strips of Nichrome  80/20 and a 300x300x3mm aluminum sheet and then calculate the convection heat transfer from the Al sheet to the air.

Conjugate Heat transfer Analysis on the manifold located upstream of the ramjet fuel injector is performed using SimScale CHT V2.0 Solver. The flow field of the hot fuel JP-7 flowing through the manifold is simulated and the wall temperature of the manifold is computed. This experiment essentially duplicates the conditions of a regeneratively fuel cooled hypersonic ramjet engine flow path of heat sink construction to simulate the actual conditions the engine would be operated at by using a facility fuel heater. In order to match these conditions correctly, a detailed thermal analysis on upstream fuel delivery components(manifold) is required.

this project is to test differnet cooling plate simulations

Conjugate heat transfer is a behavioural analysis where convective (transfer between fluid) and conductive (transfer between solids) heat transfer takes place in a system. This combination of heat transfer has forced or natural convection where fluid is dominated by convection and solid is dominated by conduction. 
Objective of the Experiment is to
Carry out mesh Independent study
Stimulate CHT using two different processor materials
Carry out the analysis at different velocities 
To determine the hot spots and Heat transfer co-efficient at different velocities

CHT  in Cylinder with internal thermal mass of water

Check out www.simscale-academy.com for more classes on simulation.

This project is do a analysis on the temperature versus time when a PCB Copper bar (exposed to the air) is subjected to a 34.9 amp current that produces 0.008185 Watts within the piece.

conjugate heat transfer | SimScale Project Library | Page 2